Synergy Jeep Heavy Duty Replacement Tie Rod Ends

Part #: 4131

Weight: 2 lbs

Description

Synergy Jeep Heavy Duty Replacement Tie Rod Ends
Fully greaseable sintered metal-on-metal bushing design has high wear resistance
Specially designed grease grooves in the OD of the ball to allow for maximum lubrication
Spring loaded bearing design keeps pressure on bearings and keeps the joint tight as it wears
Forged bearing housing made from 1018 steel for a strong, smooth, bearing surface
Tie Rod End stud made from 4140 steel with an induction heat treated bearing surface for smooth operation and maximum life
Single Plane tie rod ends offer misalignment in one direction of movement only. This eliminates drag link flop on the products they are designed for
Outperforms the factory and all other aftermarket style tie rod ends by offering a larger shank with no stress riser (doesn't neck down at base) and elimination of the nylon ball race
Boots are made from tear/wear resistant black NBR and come with retaining springs
Includes all necessary hardware for installation
7/8-18 UNF LH or RH Thread available

4131-L are designed specifically to be used in the following Synergy products:

8000-01 Drag Link (knuckle side only)
8001 Drag Link (knuckle side only)
8002-15 Tie Rod

4135-L and 4135-R are designed specifically to be used in the following Synergy product:

8121-01 Tie Rod (1x 4135-L and 1x 4135-R)

4135-L and 4137-L are designed specifically to be used in the following Synergy product:

8121-02 Drag Link (1x 4135-L (pitman arm side) and 1x 4137-L (knuckle side))

4139-L are designed to be used in the following products:

8000-01 Drag Link (pitman arm side only)
8001 Drag Link (pitman arm side only)
8002-15 Tie Rod (One side only)

Synergy High Performance Grease (4119) is the recommended grease for this product

Part #	Description	Thread	Style
4131-L	HD Tie Rod End, Left Hand Thread for JK's	7/8-18 Left Hand	Standard
4131-R	HD Tie Rod End, Right Hand Thread for JK's	7/8-18 Right Hand	Standard
4135-L	HD Tie Rod End, Left Hand Thread for TJ/XJ/ZJ's	7/8-18 Left Hand	Standard
4135-R	HD Tie Rod End, Right Hand Thread for TJ/XJ/ZJ's	7/8-18 Right Hand	Standard
4137-L	HD Tie Rod End, Left Hand Thread for TJ/XJ/ZJ's	7/8-18 Left Hand	Single Plane
4139-L	HD Tie Rod End, Left Hand Thread for JK's	7/8-18 Left Hand	Single Plane
4162-L	HD Tie Rod End, Left Hand Thread for JL / JT Drag Link	1-14 Left Hand	Single Plane
4163-L	HD Tie Rod End, Left Hand Thread for JL / JT Drag Link and Tie Rod	1-14 Left Hand	Standard
4164-L	HD Tie Rod End, Left Hand Thread for JL / JT Tie Rod	1-14 Left Hand	Single Plane
4166-L	Conversion Tie Rod End (Pitman side). Adapts 8000-01 Drag Link for JL / JT with Ultimate Dana 60 axle housings only.	7/8-18 Left Hand	Single Plane

Tie Rod End Fitment Table

Fitment	Description	Driver Side Tie Rod End	Driver Side Tie Rod End Boot	Passenger Side Tie Rod End	Passenger Side Tie Rod End Boot
8000-01	JK / JKU Drag Link	4139-L	4131-01	4131-L	4131-01
8002-15	JK / JKU Tie Rod	4139-L	4131-01	4131-L	4131-01
8121-01	TJ / LJ / XJ / ZJ / MJ Tie Rod	4135-L (Either side)	4131-01	4135-R (Either side)	4131-01
8121-02	TJ / LJ / XJ / ZJ / MJ Drag Link	4135-L	4131-01	4137-L	4131-01
8800-01	JL / JLU / JT Drag Link	4162-L	4131-01	4163-L	4131-01
8802-01	JL / JLU / JT Tie Rod	4163-L	4131-01	4164-L	4131-01

413X Exploded View

Comparison

GM 1 Ton Replacement w/ Nylon Bushing

WARNING: Operating, servicing and maintaining a passenger vehicle or off-road vehicle can expose you to chemicals including engine exhaust, carbon monoxide, phthalates, and lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. To minimize exposure, avoid breathing exhaust, do not idle the engine except as necessary, service your vehicle in a well-ventilated area and wear gloves or wash your hands frequently when servicing your vehicle.
For more information go to www.P65Warnings.ca.gov