Synergy 2005+ Ford Super Duty F-250 / F-350 Heavy Duty Steering Kit

Synergy 2005+ Ford Super Duty F-250 / F-350 Heavy Duty Steering Kit was designed with the end user in mind. The tie rod and drag link will bolt directly into the stock location for an immediate upgrade in steering feel and strength. There are no wheel size requirements; factory wheels and tires are 100% compatible! The tie rod is made from heat treated 1.75" 4130 chromoly for maximum strength. The drag link is made from 1.5" 1026 DOM USA made steel tubing and is machined to retain the stock steering stabilizer, if desired. 

Pair this kit with one of our upgraded stabilizer kits for the most complete steering kit on the market! Offered with single stabilizers in both the stock and a low tie rod mounting locations as well as dual stabilizer configurations so you can select the best fit for your application. 

Fitment:

Additional stabilizer configurations are available! See "Optional Additional Configurations" below.

Benefits:

• Heavy Duty Drag Link is precision bent to clear factory axle brackets and is compatible from stock to 4" lifted vehicles; Vehicles over 4" of lift will require a drop pitman arm for compatibility
• Heat treated tie rod is over 40% stronger than OEM and formed post heat treating for superior strength
• Engineered for maximum articulation, the heavy duty tie rod is bent to clear sway bar mounts, differential cover, and steering pitman arm
• Synergy Heavy Duty Tie Rod Ends are larger, stronger, and more durable than stock and include grease fittings and dust boots with retaining rings for easy maintenance
• Single plane tie rod ends eliminate unwanted drag link or tie rod movement and prevent the dead spot when changing direction
• Kit is fully adjustable while installed in the vehicle, thanks to our Double Adjuster Sleeve and Pinch Bolt Assembly
• Both the tie rod and drag link are fully sealed from the elements thanks to our Forged Pinch Bolt housings and complete welded assembly
• Fabricated clamp designed to retain the factory stabilizer, one of our recommended FOX Stabilizers, or other aftermarket stabilizers with 1/2" mounting bolts
• Synergy single and dual stabilizer brackets can be ran while retaining a stabilizer in the factory position on the drag link
• Pinch bolt design eliminates jam nuts, preventing loosening and alignment creep
• Compatible with stock wheels and tires
• Compatible with stock steering stabilizer

Features:

• Drag link is precision bent from 1.5" x .250 wall 1026 USA made DOM
• Tie rod is engineered and bent from 1.75" x .188 wall heat treated 4130 chromoly
• Two stage abrasion resistant powder coat finish for maximum durability and corrosion resistance
• Synergy metal on metal, fully greaseable tie rod ends include a 4140 steel shank, a 1018 steel bearing housing, and capped with a heavy duty nitrile-butadiene rubber boot and retaining spring
• Synergy Double Adjuster Sleeve and Pinch Bolt Assembly for easy alignment
• 100% bolt on components assures an easy, trouble free installation with the use of basic hand tools

Min/Max Length:

Measured in a straight line from center of tie rod end to center of tie rod end

• Drag Link:
  • Min collapsed length: 42.625" 
  • Max extended length: 45"
• Tie Rod:
  • Min collapsed length: 59.75"
  •  Max extended length: 62.5"

Includes:

Notes:

• Drag Link Replacement Tie Rod Ends:
  • (1) 4153-L - Driver
  • (1) 4152-L - Passenger
• Tie Rod Replacement Tie Rod Ends: 
  • (1) 4150-L - Driver
  • (1) 4151-L - Passenger
• Additional recommended Fox Steering Stabilizers:
  • IFP - Internal Floating Piston 6401-XX
  • TS - Through Shaft 6402-XX
  • ATS - Adjustable Through Shaft 6403-XX
  • For a complete kit, check out part number 8610-30
• Select your steering stabilizer based on the intended stabilizer configuration
• Recommended to be used with Synergy Steering Stabilizer Clamps 4050-50 (drag link) or 4050-75 (tie rod)
• Fox TS or ATS Stabilizers require the use of (2) Synergy TS / ATS Clamp Adapters 4051-01
• 4.75" backspacing wheels or less required for use with TS and ATS stabilizers
• Synergy 1-1/2" Stabilizer Clamps 4050-50 are not required when running our recommended FOX TS & ATS Stabilizers
• Compatible on vehicles with up to 3" of ride height with stock pitman arm & track bar bracket. Compatible on vehicles with 4"+ lift with drop pitman arm and track bar drop bracket.
• Synergy High Performance Grease part number 4119 to be used with all Tie Rod Ends
• Synergy Premium Copper Infused Anti-Sieze 4118 to be used with all threaded components

Optional Additional Configurations:

• Linear Dual Stabilizers - 8610-02 plus your choice of FOX IFP, FOX TS, or FOX ATS stabilizers

 Installation Instructions - 8600-01

 Installation Instructions - 8602-11

More information: www.p65warnings.ca.gov